Category Archives: X Axis Stage

Motion Control – ZrO2 Zirconia Ceramic Radial Ball Bearings For High Loads available from LM76 are FDA/USDA/3A-Dairy Compliant!

Motion Control – Zirconia Ceramic Radial Bearings
motion control radial bearings

E. Longmeadow, MA — Motion Control – LM76 has announced the release of their new line of Radial Ball Bearings featuring ZrO2 (Zirconia) Ceramic balls. To Complement LM76’s broad range of Linear Bearings that are FDA/UDSA/3A Dairy compliant, as well as linear bearings for extreme environments; they have added Deep Groove bearings which accommodate radial and axial loads, Angular Contact bearings for simultaneously handling radial and axial loads, Spherical Bearings which are self aligning, and Thrust Bearings for high axial loads. Each of the four types of metric bearings are available in a wide range sizes.

motion control - linear motion products

The advantages of ZrO2 ceramic balls are: FDA/USDA/3A Dairy/Caustic washdown compliant, lighter than steel balls and can be used at extreme RPMs, they withstand higher loads without spalling, have a lower coefficient of friction, are inert to chemicals, have no magnetic signature, and are non conductive.

Motion Control – Electric Cylinder from Moticont Has Zero Cogging and High Throughput!

Motion Control – Electric Cylinder Has Zero Cogging

 

motion control - electric cylindermotion control - moticont

 

Van Nuys, CA — Motion Control – Moticont has added another non-commutated linear actuator to its DDLM series of low cost actuators.

The 0.125 in. (3.2 mm) diameter shaft has an internal thread on each end, a total of length of 4.960 in (126.0 mm), and extends 1.585 in. (40.3 mm) past the mounting end of the actuator. The shaft extends thru the 3/8-32 UNF x 0.250 (6.4 mm) long threaded studs at each end of the housing which can be used for mounting the DDL-019-070-01 linear actuator. Long life plain linear bearings support the internal shaft at both end of the actuator.

Motion Control – Low Cost 1, 2, 3, and 4 ADAGIO Axis Stepper Motor Motion Control Systems Available from Optimal Engineering Systems, Inc. (OES)!

Motion Control – Stepper Motor Motion Control Systems

motion control - stepper motor controller


motion control - stages - custom

 

 

 

Van Nuys, CA – — Motion Control – To complement the Optimal Engineering Systems’ (OES) expanding line of single and multi-axis motion control stages, OES has added the ADAGIO-X-STPR Series of Motion Control Systems.

Motion Control – Rotational Voice Coil Stage quickly and repeatably steers an optical beam with a diameter of up to 25 millimeters over 90° with 25 microradians of resolution!

Motion Control – Rotational Voice Coil Stage

Quickly and repeatably steer an optical beam with a diameter of up to 25 millimeters over 90° with 25 microradians of resolution!

RVC-9025 Rotational Voice Coil Stage: Up to 25mm wide mirror; Controllable positioning over +/-45 degree optical; 5 arcsec (25 microradians) optical position repeatability; 1 degree optical step-and-settle in less than 5ms; Fully integrated servo controller; USB 2.0 and auxilary user electrical interfaces; X 58 x 28 x 21 millimeters, 30 grams

motion control - miniature stages

Forestville, CA – The RVC-9025 Rotational Voice Coil Stage provides a means to quickly and accurately set an angular position. The frequency is factory adjusted to customer specifications during the manufacturing process. Amplitude of the resonating mirror can be adjusted through either an analog input voltage or the USB interface.

motion control - miniature components

An optional high-resolution position feedback sensor can be monitored by an analog output signal on the User Connector. The RS-25 Resonant Scanner can also be configured with a high-resolution 16-bit Analog to Digital Converter to quickly sample and report the mirror position at any moment if the position sensor is included.

Motion Control -What To Consider When Specifying A Linear Slide

Motion Control – Tutorial

Considerations when specifying a linear slide for a new or existing application.

By Mike Quinn • LM76

When a design engineer has fully defined a linear-motion application’s requirements regarding travel length, speed, force, and accuracy as well as repeatability, the next question to answer is this:

Does an off-the-shelf linear slide (or a stock linear slide from a catalog) fully satisfy the application?

motion control - lm76

Off-the-shelf linear slides are advantageous for their quick delivery and lower cost than that of custom components. No wonder most linear-motion designs do in fact employ off-the-shelf linear slides from various component and system suppliers.

motion control - linear stage

Motion Control – Low Cost, Long Range of Travel, High Precision, Low Profile, Motorized, Profile Rail Linear Guide Stages Are Available from OES

Motion Control – Profile Rail Stages

motion control - linear stages


motion control -oesVan Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) has added five new profile single axis positioning stages to their AQ150 Series of linear stages. Available off-the-shelf in travel lengths of: 600 mm (23.622 in.), 700 mm (27.559 in.), 800 mm (31.496 in.), 900 mm (35.433 in.), and 1000 mm ( 39.370 in.), these stages are available with either a Two-Phase Stepper Motor or with a Three-Phase Brushless Motor with a Quadrature Incremental Optical Encoder.

Motion Control – Linear Focus Actuator from Equipment Solutions!

Motion Control – Linear Focus Actuator

motion control - linear focus actuator

 

Equipment Soultions

Forestville, CA – The LFA-1205 Linear Focus Actuator is a high performance compact positioning system.  It was specifically developed for optical applications requiring both high precision and high-speed positioning over a short to medium stroke.  The LFA-1205 is well suited for optical focusing and other micropositioning applications such as scanning interferometry, surface structure analysis, disk drive testing, autofocus systems, confocal microscopy, bio-technology, semiconductor test equipment.  Note that this motor is normally configured with an analog position feedback sensor and can be optionally equipped with a digital quadrature feedback element.    The key to this products immense success is its novel tubular architecture.  This arrangement provides a means to send the optical path directly through the middle of the motor.  The moving optic attached to the motors ‘C-mount’ is not cantilevered and so has no torques.  The LFA-1205 Linear Focus Actuator is directly compatible with the SCA814 Servo Controlled Amplifier.

 

  • 12 Millimeter clear aperture
  • 5 millimeters of linear motion
  • <50 nanometer positioning repeatability
  • Small Step Response of <1 millisecond
  • Threaded lens mount 70 x 70 x 50 millimeters, 600 grams

 

motion control - miniature focus actuator

By design, the LFA-1205 Linear Focus Actuator rotates approximately 0.1 degrees or 1.7 milliradians for every 1 millimeter of translation.  Through manufacturing tolerances only there can be a small amount of pitch and roll motion that is induced during the intended translation.  These small but real error sources are routinely characterized during the manufacturing process  using our AC400 Digital Autocollimator to control product uniformity.

motion control - interface drawing

Click on Links below for:

Motor Force Constant

Position Nonlinearity

Flexure Spring-Rate

Equipment Solutions, Inc. (ESI) is a provider of engineering and manufacturing services. ESI specializes in the design and production of automation and instrumentation products including motion control components and sub systems. ESI’s products range from galvanometer amplifiers with an integrated arbitrary waveform generator, to high-resolution displacement sensors, voice coil and stepper motor stages, amplifiers and controllers.

For additional information contact Jeff Knirck at Equipment Solutions,Inc. Mailing Address – PO Box 159, Forestville, CA 95436; Shipping Address 6490 Front Street, Forestville, CA 95436; Tel: 408-245-7162, Fax: 408-245-7160, E-Mail: info@equipsolutions.com or visit the Website at http://www.equipsolutions.com


See this and other Motion Control Components from Equipment Solutions featured on:

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://MotionControlBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

http://Gotcha-Stick.com

http://MotionControlMarketing.com

Equipment Soultions
Visit our Website
Motion Control - Follow Equipment Solutions on Twitter
Motion Control - Follow Equipment Solutions on Facebool
View Equipment Solutions Motion Control Blog

Motion Control – High Precision, Low Profile, Motorized, Ball Bearing Linear Guide Stages!

OES Logo

Van Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) offers two series of low cost, low profile, motorized ball bearing linear guide (profile rail) positioning stages. The AQ140 Series and the AQ150 Series of linear stages are available off-the-shelf in travel lengths of: 50 mm (1.969 in), 100 mm (3.937 in), 150 mm (5.905 in), 200 mm (7.874 in), 300 mm (11.811 in), 400 mm (15.748 in), 500 mm (19.685 in). These 2 µ resolution stages (achieved with a 10 micro-steps per step stepper motor driver) are ideal for: Laser machining, testing, pick-and-place, inspection, sorting, wafer handling, semiconductor, assembly, metrology, and photonics in industrial, laboratory, and medical applications.

The tables, depending on length of travel, measure 120 x 120 mm (4.73 in x 4.73 in.), 150 x 150 mm (5.90 in x 5.90 in.) and 160 x160 mm (6.30 in x 6.30 in.) The AQ150 Series has top and side rail covers. Featuring a 4 mm per turn, precision 2 µ backlash lead screw, typical performance specifications of the AQ140 and AQ150 linear stages include: repeatability of 5 µ, positional accuracy 8 µ, straightness 6 µ, driving parallelism 15 µ, pitching 25 arc seconds, and deflection 25 arc seconds.

Constructed of aluminum and black anodized, these stages can handle loads to 30 kg (66 lbs.) and 50 kg (110 lbs.). These low profile stages can easily be ordered in an XY or XYZ configuration. There is a knob on the back of the motor for manual adjustments or it can be replaced with an encoder. An optional servo motor, encoder, and brake are also available. These compact linear stages are easily integrated into new and existing systems and are available as with complete plug-and-play systems or with a plug-in motor driver. For details concerning each stage in the series please go to http://oesincorp.com/motorized-linear-stages/low-cost-series/index.htm

About OES – Optimal Engineering Systems, Inc. (OES) is a manufacturer of motion control products including: Stepper motor controllers and drivers, solenoid electronics, and positioning stages and slides. Applications include: Animation, automated assembly systems, automation, CNC machines, flight simulation, inspection systems, linear and rotary stages, machine tools, medical devices, motion control camera boom systems, optical comparators, CMMs, pan-tilt gimbals, PCB assembly & inspection, pick-and-place, positioning stages, robotics, scanners, security cameras, telescope drive mechanisms, time-lapse photography and winders.

Some of the industries OES serves are: Aerospace, Astronomy, Chemical, Communications, Educational Institutes, University, Colleges, Government Agencies, National Labs, Manufacturing, Medical, Metrology, Military, Motion Control, Museum, News Agencies, Semiconductor and Test Equipment. Optimal Engineering Systems, Inc’s. competitive advantage is its state-of-the-art in-house manufacturing facility in North America enabling OES to supply clients with custom designed orders or high volume just-in-time deliveries globally.

For additional information, contact sales team at: OES, 6901 Woodley Ave.; Van Nuys, CA 91406; Telephone: 888-777-1826 or +1 818-222-9200, FAX +1 818-436-0446 or E-Mail: sales@oesincorp.com or visit the website at http://www.oesincorp.com

OES Logo
Visit OES Website
OES Facebook
OES Twitter
OES Videos