Category Archives: Stage – High Load

Motion Control – High Precision, High Load Goniometer Stages with +/- 30 Degrees of Travel Are Available from OES!

XYZ-G Positioning Stage – XYZ-Goniometer Positioning Stages

Motion Control goniometer stage
motion control - stage

 

Van Nuys, CA – – Motion Control – Optimal Engineering Systems, Inc. (OES) has added four goniometers to their expanding catalog of high precision positioning stages. The new, AK160-30 Goniometer Series feature precision ground worm gears with a 400:1 ratio and pre-loaded cross roller guides offer +/- 30 degrees of travel with 30 kg of load.

Motion Control – NEW! A Series of 600 mm to 1000 mm High Precision Ball Bearing Linear Guide Stages Available from OES!

Motion Control – Vertical Rotary Stage

motion control - linear stagemotion control - OES

 

 

 

Van Nuys, CA – — Motion Control – A series of long travel, low cost, low profile, motorized, profile rail positioning stages are now available from Optimal Engineering Systems, Inc. (OES). The AQ140 Series of linear stages are available off-the-shelf in travel lengths of: 600 mm, 700 mm, 800 mm, 900 mm, and 1000 mm. These high precision stages can be ordered with a Two-Phase Stepper Motor (pictured) which feature resolutions of 2 micron and 1.25 micron (achieved with a 10 or 20 micro-steps per step stepper motor driver), and up to 80 mm per sec of travel.

Motion Control – High Load, Low Profile XY Stage Features High Resolution and High Repeatability Is Available from OES!

Motion Control – XY High Resolution Stage

motion control - high load stage

motion control - OES Components

 

 

 

Van Nuys, CA – — Motion Control – OES (Optimal-Engineering Systems, Inc.) has added a new, larger, high load, precision stage to it’s extensive line of precision XY stages. The AU200-170×170 stage is a low profile stage measuring just 108 mm (2.252 in) high with a compact footprint (including the motors) of 458.5 mm x 458.5 mm (18.032 in.).

Motion Control – Features of 600 MM Vertical Lift Stage Include: Stability, High Loading, Low Cost, and 5 Micron Repeatability!

Motion Control – 600 MM Vertical Lift Stages

motion control - vertical lift stage
motion control - stage

 

 

 

Van Nuys, CA – Motion Control – The new AT20-600 series of Motorized Vertical Lift Stages from Optimal Engineering Systems, Inc. (OES) features a vertical lift of 600 mm.  The AT20-600-01 (pictured) is driven by a Two-Phase Stepper Motor features a repeatability of 5 microns, positional accuracy of 20 microns and has a knob on the motor for manual adjustment. The AT20-600-02 is driven by a Brushless DC Servo Motor with a Quadrature Incremental Encoder and the AT20-600-03 is driven by a DC Servo Motor with a Quadrature Incremental Encoder.  Each of the Servo Motor options, the -02 and -03 versions, offer higher travel speeds, increased positional accuracy, and repeatability.  The AT20-600-04 is driven by a Two-Phase Stepper Motor with a Quadrature Incremental Encoder mounted on the motor for position verification.

Motion Control – High Precision Four-Axes Positioning Stages with Four Motor Options

Motion Control – Four Axes Positioning Stages

motion control - four axes stages
motion control - stage

 

Van Nuys, CA – Motion Control – OES (Optimal Engineering Systems, Inc.) has added to their extensive line of purpose-built stages.  The new XYZR Series of Four-axes Stages are the integration of a: 15 mm, 30 mm, 50 mm, 75 mm, or 100 mm linear stages (in any combination) for the X, Y, and Z axes, and a 60 mm or 100 mm diameter rotary stage capable of 360 degrees of continuous rotation.  These stages are the ideal choices for: Laser scanning, drilling, and machining, reverse engineering, inspection, assembly, measurements, tracking, and positioning.

OES – All New! High Precision, Three-axis Gimbal Mounts with Four Motor Options Offer Greater Flexibility and Stability!

OES – NEW! Three-axis Gimbal Mounts!
OES- gimbal mount

OES - motion control - OES Components

 

 

 

Van Nuys, CA – OES (Optimal Engineering Systems, Inc.) has released four all new Three-axis Azimuth, Angular Elevation, and Roll Gimbal Mounts. These new high precision and high stability AU270-AER Gimbal Mounts locate the surface of the Roll Stage 115 mm below the center line of rotation allowing for the positioning of: Cameras, optics, lasers and instrumentation for scanning, tracking, positioning, pointing, and other applications on their respective centerlines.

Motion Control – Open Aperture XY Alignment Stages Feature: 120 mm x 120 mm of Travel, and 1 Micron Repeatability!

Motion Control – Open Aperture XY Alignment Stages

motion control - alignment stage
motion control - stage

 

 

 

Van Nuys, CA – Motion Control – Optimal Engineering Systems, Inc. (OES) has released four new high resolution, high repeatability XY Alignment Stages. The AU200-120×120 Alignment Stages feature 120 mm (4.724 in.) of travel in both the X and Y axes.  These new low profile 87 mm (3.425 in.) high XY stages, have a 188 mm x 188 mm (7.401 in. x 7.401 in.) open aperture.  Easy integration of tooling and fixtures is facilitated through a precision series of threaded mounting holes.

Motion Control – Four Axes XYZ-Goniometer Stages with Four Motor Options Features Positional Accuracy to 10 Microns!

Motion Control – XYZ-Goniometer Positioning Stages

motion control - xyz goniometer stages
motion control - stage

 

Van Nuys, CA – Motion Control – OES (Optimal Engineering Systems, Inc.) is unveiling their new XYZ-Goniometer Series of Four-axes Stages.  Any of the three Goniometers Stages with +/- 10 degrees, +/- 15 degrees or +/- 45 degrees of travel can be integrated with X, Y, and Z axis stages with 15 mm, 30 mm, 50 mm, 75 mm, or larger than 100 mm of linear travel linear in any combination of X, Y, and Z axes.  These stages are the ideal choices for: Crystallography, metrology, light measurement, mirror positioning, laser scanning, drilling and machining, reverse engineering, inspection, assembly, measurements, tracking, and inspection and optical bench applications.

Motion Control – 1, 2, 3 and 4 Axes of Motion Controllers for Servos and Steppers are Low Cost and Plug-and-Play!

Motion Control – Motion Controllers for Servos and Steppers!


Van Nuys, CA – — Motion Control – Need a quick and easy solution to install a single or multi-axis Plug-and-Play motion controller? The answer: The MCC Series of stepper and servo motor controllers from OES (Optimal Engineering Systems) which are designed to control from one to four axes of motion for users without prior motion control experience. These MCC controllers integrate a motion control card and operator interface in one package. Having a user-friendly interface, they allow the user to operate the motion controller, without the need for a PC, PLC, host controller, or programming.

motion control - stages - custom

 

 

The modes of operations are: Set Acceleration, Set Velocity, Set Position, Absolute Move, Relative Move, Find Home, Reset Position Counter, Go to Position Zero, Joystick Operation and Stop All Motors. The MCC Controllers feature a 4-Line LCD, 32-button keypad, STEP and DIRECTION outputs for each axis.

Motion Control – High Precision 300 MM Motorized Vertical Lift Stage from OES Features: Stability, High Load Capability, and Low Cost!

Motion Control – Vertical Lift Stage

motion control - vertical lift stage

motion control - OES Components

 

 

Van Nuys, CA – — Motion Control – A vertical lift of 300 mm (11.811 in.), high stability, and low cost are just some of the features of the AT20-300 Motorized Vertical Lift Stage from Optimal Engineering Systems, Inc. (OES). This high load, 50 kg (110.2 lbs), vertical lift stage can be easily integrated into almost any application. The large 400 mm x 200 mm (15.748 in. x 7.874 in.) stage has a pattern of threaded mounting holes. The rigid box construction of the moving component of the elevator stage travels on six slide rails assuring smooth vertical travel and parallelism of the table and mounting surface at all times, and features: 3.315 µ (non- Micro-Step) resolution, 5 µ repeatability, and 15 µ positional accuracy.

Motion Control – NEW! Elevator Stages from OES Feature 0.03 micron Resolution!

Motion Control – 0.03 micron Resolution Elevator Stage!

motion control - elevator stage


motion control - OES

 

 

 

Van Nuys, CA – — Motion Control – Two new motorized elevator stages, the DAG20-120-01 and the DAG20-120-04 have been released by Optimal Engineering Systems, Inc. (OES).  These high resolution, compact, low profile elevator stages feature high stability 120 mm x 120 mm tables and 20 mm of vertical travel.  High precision ball bearing profile rails assure very high parallelism and smooth motion throughout the raising and lowering of the table.  These Z-Axis Stages are ideal for: Microscopy, inspection, metrology, positioning, photonics, sampling, and laser drilling and machining.

Motion Control – Open Aperture XY Stages from OES Feature: High Resolution and High Repeatability!

Motion Control – Open Aperture XY Stages!

motion control- xy stages

Van Nuys, CA – — Motion Control – Two new high resolution, high repeatability XY stages have been released by Optimal Engineering Systems, Inc. (OES). The AU200-15×15-01 Motorized Stage (pictured) and the AU200-15×15-04 Motorized Stage are powered by Two-Phase Stepper Motors and have high 0.25 micron resolution and high 1.5 micron repeatability.

motion control - OES

The AU200-15×15-04 stage includes Quadrature encoders for position verification. Both stages have a large 3.54 in. x 3.54 in. (90 mm x 90 mm) platform with large open aperture and feature standard 1 mm-per-turn ground lead screws, and precision V-grove and Cross Roller guides.

Motion Control – Positioning Stage Has 3,890 lbs Load Capacity!

Motion Control – Linear Positioning Stage

motion control - linear stages
motion control - electromate robotics

 

 

 

Vaughan, Ontario, Canada -Motion control – LINTECH’s 160 series tables are designed to
maximize performance while minimizing physical size and
cost. These tables use a low friction, preloaded, recirculating linear ball bearing system, which rides on precision ground linear rails. The linear rails are mounted to an aluminum base, which offers a rigid support over the entire travel of the table’s carriage.

Motion Control – Dual Axis Yaw-and-Pitch Stages Feature Full Range of Motion of Each Axis Under a Single Fixed Point in Space!

Motion Control – Yaw and Pitch Stages

motion control - yaw pitch stage


Van Nuys, CA – Motion Control – A new, series of Dual-axis Yaw-and-Pitch Stages have been introduced by OES (Optimal Engineering Systems, Inc.). This new series of high precision Yaw-and-Pitch stages are ideal for precise measurements of compound curves and angles of an object during inspection or reverse engineering, laser machining and drilling, scanning, tracking, mirror positioning, and for use with coordinate measuring machines and autocollimators.

motion control - stage

The YP100-45 Series of Yaw-and-Pitch Stages were developed through the integration of a rotary stage (yaw axis) and a goniometer (pitch axis) having a travel range of +/- 45 degrees.

Motion Control – Low Cost 1, 2, 3, and 4 ADAGIO Axis Stepper Motor Motion Control Systems Available from Optimal Engineering Systems, Inc. (OES)!

Motion Control – Stepper Motor Motion Control Systems

motion control - stepper motor controller


motion control - stages - custom

 

 

 

Van Nuys, CA – — Motion Control – To complement the Optimal Engineering Systems’ (OES) expanding line of single and multi-axis motion control stages, OES has added the ADAGIO-X-STPR Series of Motion Control Systems.

Motion Control – Miniature Size, High Precision, Hollow Core, 39 mm Diameter Rotary Stage from Optimal Engineering Systems, Inc. (OES)!

Motion Control – Miniature Hollow Core Rotary Stage

motion control - rotary table


motion control - OESVan Nuys, CA – Motion Control – Optimal Engineering Systems, Inc. (OES) has introduced a high precision, low profile, miniature size rotary table, the AR39-AH. This high precision miniature size rotary stage is just 35 mm (1.378 in.) high and the footprint including the standard 2-phase 1.8 degree stepper motor is only 58 mm (2.283 in) by 100.5 mm (3.957 in ). The table has a precision pattern of 6 8-M2x4L threaded mounting holes in the rotary table for fixtures or tooling, and an 8 mm (0.315 in) diameter through hole. Countersunk holes in the base allow for easy unobstructed integration into new and existing applications. The diameter of the AR39-AH Miniature Rotary Table is 39 mm (1.535 in.) and range of travel is a full 360 degrees of continuous rotation.

Motion Control -What To Consider When Specifying A Linear Slide

Motion Control – Tutorial

Considerations when specifying a linear slide for a new or existing application.

By Mike Quinn • LM76

When a design engineer has fully defined a linear-motion application’s requirements regarding travel length, speed, force, and accuracy as well as repeatability, the next question to answer is this:

Does an off-the-shelf linear slide (or a stock linear slide from a catalog) fully satisfy the application?

motion control - lm76

Off-the-shelf linear slides are advantageous for their quick delivery and lower cost than that of custom components. No wonder most linear-motion designs do in fact employ off-the-shelf linear slides from various component and system suppliers.

motion control - linear stage

Powered by WordPress and ThemeMag