Category Archives: Driver – Microstepping

Motion Control – Excellence Canada announces Electromate is a recipient of the 2021 Canadian Business Excellence Awards for Private Businesses!

motion control - electromate


motion control - electromateTORONTO, Canada — Motion Control – TORONTO, May 21, 2021 (GLOBE NEWSWIRE) – Electromate Inc. is pleased to announce that, at the upcoming fifth annual Canadian Business Excellence Awards for Private Businesses being held on Wednesday June 9th, Excellence Canada will be awarding Electromate with their Canadian Business Excellence Award.

“Recipients of this distinguished award have clearly demonstrated a strategic approach to successfully improving business performance and achieving goals, with a focus on the following three key performance areas: Delighted Customers; Engaged Employees; and Innovation,” says Allan Ebedes, President and CEO, Excellence Canada.

Excellence Canada’s mission is to help improve organizational performance and recognize excellence, with a vision to promote and enable excellence in every organization in Canada.

Motion Control – Powerful Microstepping Drive from Servo2Go!

Applied Motion’s powerful stepper drive costs the same as a competitors drive without a built-in power supply!

Servo2Go-Logo

Greenville, DE –— The Motion Control STAC5 microstepping drive provides up to 5 amps per phase from a high bus voltage with sophisticated current control, delivering high torque over a board range of speeds. An advanced anti-resonance algorithm with electronic damping allows for maximum torque utilization and fast settling times.

The STAC5 microstepping drive is available in 120VAC and 220VAC versions, both housed in a compact package.

Applied Motion’s powerful stepper drive costs the same as a competitors drive without a built-in power supply, and features……

  • High performance
  • Built-in power supply & regeneration clamp
  • 120 and 220 VAC models
  • Accepts pulse & direction, streaming commands, stored programming
  • 10/100 MBit Ethernet & EtherNet/IP
  • Advanced anti-resonance
  • Matching high performance motors

All Motion Control STAC5 models include 100Mbit Ethernet communication. The Ethernet interface is used to configure the STAC5 and motor, and also supports the SCL and Q languages over standard Ethernet cabling, addressing and protocols.There are 3 control options available with the STAC5 stepper drives: S, Q and IP.

T• “S” drives can operate in pulse & direction, velocity, and streaming serial (SCL) control modes. To select the control mode, as well as to setup the motor and configure other drive parameters, use the ST Configurator™ software.

• “Q” drives can operate in all of the same control modes as an S drive, plus they have the ability to run stand-alone Q programs stored in non-volatile memory. Q programs are created using the Q Programmer™ software, which provides multi-tasking, math functions, conditional processing, data register manipulation, and more features in a robust yet simple text-based programming language. Like S drives, Q drives must first be setup and configured using the ST Configurator™ software.

• “IP” drives come with built-in EtherNet/IP network communications, the widely used industrial protocol for manufacturing automation applications. With EtherNet/IP users can control, configure and query the drive using an open, standards-based, industrial Ethernet connection at speeds up to 100 MBits/sec. The STAC5-IP drives run all of the same control modes as STAC5-Q drives, with the addition that all drive features can be accessed over EtherNet/IP, including more than 100 commands and 130 registers for controlling motion, I/O, configuration, polling, math, register manipulation, and Q programming. STAC5-IP drives are setup and configured using ST Configurator™, and Q programs are created using Q Programmer™.

An encoder feedback option provides position verification, stall detection and/or stall prevention. Applied Motion’s proprietary stall prevention algorithm monitors rotor lag and automatically reduces speed or acceleration to avoid motor stalls, allowing 100% torque utilization. high torque. These are three-phase brushless motors with hall signals for commutation and velocity loop feedback.

The STAC5 can be purchased with a wide range of high torque step motors, optimized for use with the drive. Three lengths of HT23 are available in single and double shaft configurations: HT23-552, HT23-553 and HT23-554, with holding torque ranging from 84 to 255 ounce-inches. Three lengths of HT34 are also available in single and double shaft configurations: HT34-495, HT34-496 and HT34-497, with holding torque ranging from 550 to 1700 ounce-inches.

For more information on the STAC5 Stepper Drives from Applied Motion Products, click on the link below —

https://www.servo2go.com/product.php?ID=105241&cat

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-02401- 877-378-0240 or e-mail Warren Osak at warren@servo2go.com or visit Servo2Go.com at: www.Servo2Go.com

Servo2Go-Logo
Twitter Link
Facebook Link

Motion Control – Powerful Microstepping Drive from Servo2Go!

Applied Motion’s powerful stepper drive costs the same as a competitors drive without a built-in power supply!

Servo2Go-Logo

Greenville, DE –— The Motion Control STAC5 microstepping drive provides up to 5 amps per phase from a high bus voltage with sophisticated current control, delivering high torque over a board range of speeds. An advanced anti-resonance algorithm with electronic damping allows for maximum torque utilization and fast settling times.

The STAC5 microstepping drive is available in 120VAC and 220VAC versions, both housed in a compact package.

Applied Motion’s powerful stepper drive costs the same as a competitors drive without a built-in power supply, and features……

  • High performance
  • Built-in power supply & regeneration clamp
  • 120 and 220 VAC models
  • Accepts pulse & direction, streaming commands, stored programming
  • 10/100 MBit Ethernet & EtherNet/IP
  • Advanced anti-resonance
  • Matching high performance motors

All Motion Control STAC5 models include 100Mbit Ethernet communication. The Ethernet interface is used to configure the STAC5 and motor, and also supports the SCL and Q languages over standard Ethernet cabling, addressing and protocols.There are 3 control options available with the STAC5 stepper drives: S, Q and IP.

T• “S” drives can operate in pulse & direction, velocity, and streaming serial (SCL) control modes. To select the control mode, as well as to setup the motor and configure other drive parameters, use the ST Configurator™ software.

• “Q” drives can operate in all of the same control modes as an S drive, plus they have the ability to run stand-alone Q programs stored in non-volatile memory. Q programs are created using the Q Programmer™ software, which provides multi-tasking, math functions, conditional processing, data register manipulation, and more features in a robust yet simple text-based programming language. Like S drives, Q drives must first be setup and configured using the ST Configurator™ software.

• “IP” drives come with built-in EtherNet/IP network communications, the widely used industrial protocol for manufacturing automation applications. With EtherNet/IP users can control, configure and query the drive using an open, standards-based, industrial Ethernet connection at speeds up to 100 MBits/sec. The STAC5-IP drives run all of the same control modes as STAC5-Q drives, with the addition that all drive features can be accessed over EtherNet/IP, including more than 100 commands and 130 registers for controlling motion, I/O, configuration, polling, math, register manipulation, and Q programming. STAC5-IP drives are setup and configured using ST Configurator™, and Q programs are created using Q Programmer™.

An encoder feedback option provides position verification, stall detection and/or stall prevention. Applied Motion’s proprietary stall prevention algorithm monitors rotor lag and automatically reduces speed or acceleration to avoid motor stalls, allowing 100% torque utilization. high torque. These are three-phase brushless motors with hall signals for commutation and velocity loop feedback.

The STAC5 can be purchased with a wide range of high torque step motors, optimized for use with the drive. Three lengths of HT23 are available in single and double shaft configurations: HT23-552, HT23-553 and HT23-554, with holding torque ranging from 84 to 255 ounce-inches. Three lengths of HT34 are also available in single and double shaft configurations: HT34-495, HT34-496 and HT34-497, with holding torque ranging from 550 to 1700 ounce-inches.

For more information on the STAC5 Stepper Drives from Applied Motion Products, click on the link below —

https://www.servo2go.com/product.php?ID=105241&cat

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-02401- 877-378-0240 or e-mail Warren Osak at warren@servo2go.com or visit Servo2Go.com at: www.Servo2Go.com

Servo2Go-Logo
Twitter Link
Facebook Link

Motion Control – Harsh Environment Servo Drives Available from Electromate!

Motion Control - Electromate offers Food Grade HMI Display from Exor

Motion Control - Electromate-Logo

 

 

Vaughan, Ontario, Canada –Motion Control Components – Advanced Motion Controls’ Extended Environment Amplifiers are designed to operate under harsh thermal and mechanical extremes. An expanded thermal operating range allows these drives to function in both hot and cold ambient environments, and enhanced protection against shock and vibration provides additional system ruggedness. Extended Environment drives also afford benefits for applications in more docile conditions. The superior thermal capabilities reduce or eliminate the need for cooling systems such as external heat sinks and fans, enabling system designs to be more compact and to improve overall reliability.

Electromate offers Food Grade HMI Display from Exor

 

 

AMC’s Extended Environment Motion Control Servo Drives feature:

  • Shutdown Heat Sink Temperature
    • AZX-series: +105°C (221°F) — Hotter than boiling water!
    • DZX-series: +85°C (185°F)
  • Ambient Operating Temperatures
    • AZX-series: from -40° to +85°C
    • DZX-series: from -40° to +75°C
  • Complete Thermal Rise cycling in about 2 minutes
  • Shock up to 15g’s at 11 msec, ½ sine
  • Vibration up to 30grms on all 3 axes
  • Light weight
    • AZX-series: 95 grams
    • DZX-series: 105 grams
  • ~97% {max.} efficiency

Designed to assist system compliance toward:

  • MIL-STD-810F – temperature, thermal shock, humidity, altitude, shock & vibration
  • MIL-STD-1275D – characterization of 28Vdc systems
  • MIL-STD-461E – control of electromagnetic interference
  • MIL-STD-704F – aircraft power characteristics
  • MIL-HDBK-217 – reliability predictions

Click on the following link for more information on the Extended Environment Servo Drives from Advanced Motion Controls.

For further information on this new product or others in our extensive product portfolio, call 1-877-SERVO99 (737-8699) or e-mail Warren Osak at sales@electromate.com or visit Electromate at: www.electromate.com

 

Motion Control - Electromate-Logo
Visit our Website
Motion Control - Electromate Twitter Link
Motion Control - Electromate Facebook Link

NEW Lower Price for Powerful Microstepping Drive from Servo2Go!

Servo2Go - Motion Control, Applied Motion STAC5 microstepping drive

Applied Motion’s powerful stepper drive costs the same as a competitors drive without a built-in power supply!

Servo2Go-Logo

Greenville, DE –— The Motion Control STAC5 microstepping drive provides up to 5 amps per phase from a high bus voltage with sophisticated current control, delivering high torque over a board range of speeds. An advanced anti-resonance algorithm with electronic damping allows for maximum torque utilization and fast settling times.

The STAC5 microstepping drive is available in 120VAC and 220VAC versions, both housed in a compact package.

Applied Motion’s powerful stepper drive costs the same as a competitors drive without a built-in power supply, and features……

  • High performance
  • Built-in power supply & regeneration clamp
  • 120 and 220 VAC models
  • Accepts pulse & direction, streaming commands, stored programming
  • 10/100 MBit Ethernet & EtherNet/IP
  • Advanced anti-resonance
  • Matching high performance motors

All Motion Control STAC5 models include 100Mbit Ethernet communication. The Ethernet interface is used to configure the STAC5 and motor, and also supports the SCL and Q languages over standard Ethernet cabling, addressing and protocols.There are 3 control options available with the STAC5 stepper drives: S, Q and IP.

T• “S” drives can operate in pulse & direction, velocity, and streaming serial (SCL) control modes. To select the control mode, as well as to setup the motor and configure other drive parameters, use the ST Configurator™ software.

• “Q” drives can operate in all of the same control modes as an S drive, plus they have the ability to run stand-alone Q programs stored in non-volatile memory. Q programs are created using the Q Programmer™ software, which provides multi-tasking, math functions, conditional processing, data register manipulation, and more features in a robust yet simple text-based programming language. Like S drives, Q drives must first be setup and configured using the ST Configurator™ software.

• “IP” drives come with built-in EtherNet/IP network communications, the widely used industrial protocol for manufacturing automation applications. With EtherNet/IP users can control, configure and query the drive using an open, standards-based, industrial Ethernet connection at speeds up to 100 MBits/sec. The STAC5-IP drives run all of the same control modes as STAC5-Q drives, with the addition that all drive features can be accessed over EtherNet/IP, including more than 100 commands and 130 registers for controlling motion, I/O, configuration, polling, math, register manipulation, and Q programming. STAC5-IP drives are setup and configured using ST Configurator™, and Q programs are created using Q Programmer™.

An encoder feedback option provides position verification, stall detection and/or stall prevention. Applied Motion’s proprietary stall prevention algorithm monitors rotor lag and automatically reduces speed or acceleration to avoid motor stalls, allowing 100% torque utilization. high torque. These are three-phase brushless motors with hall signals for commutation and velocity loop feedback.

The STAC5 can be purchased with a wide range of high torque step motors, optimized for use with the drive. Three lengths of HT23 are available in single and double shaft configurations: HT23-552, HT23-553 and HT23-554, with holding torque ranging from 84 to 255 ounce-inches. Three lengths of HT34 are also available in single and double shaft configurations: HT34-495, HT34-496 and HT34-497, with holding torque ranging from 550 to 1700 ounce-inches.

For more information on the STAC5 Stepper Drives from Applied Motion Products, click on the link below —

https://www.servo2go.com/product.php?ID=105241&cat

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-02401- 877-378-0240 or e-mail Warren Osak at warren@servo2go.com or visit Servo2Go.com at: www.Servo2Go.com

Servo2Go-Logo
Twitter Link
Facebook Link